Tag Archives: vacuum pumps

Diaphragm Pump


Diaphragm pump (membrane pump) is an oil-free vacuum pump that is used for obtaining ‪#‎prevacuum‬ of about 0.5 mbar. The pumping in this device is based on the movement of the membrane. As the membrane is pulled down, the volume of the chamber increases, causing a drop of pressure and gas enters the chamber through the inlet. Next, the inlet is closed, outlet opened and the membrane pushed up. This causes the volume of the chamber to decrease and pressure to increase. So the gas is forced to leave the system through the outlet.

Sorption Pump


The sorption pump is an oil-free ‪#‎prevacuum‬ pump that is based on the adsorption of gases on cold surfaces. The colder the surface, the more efficient the pumping is! Therefore liquid nitrogen with a temperature less than 77 degrees Kelvin is used for cooling the adsorber. The adsorber is a porous zeolite with a very large surface area as the pores have a diameter in the range of a few nanometers (or less). If the pump is full, then it needs to be renewed by degassing, which is basically heating the adsorber so that the gas can remove the pump through the outlet.

Rotary Vane Pump


Rotary Vane Pump is an oil-based vacuum pump, that can be used to obtain ‪#‎prevacuum‬ or even medium vacuum (depending on the system). In this device the rotor and vane(s) are in the housing, that is filled with oil. When the gas enters the chamber through the inlet, it gets trapped in the oil and is transported through the working chamber with the help of the rotor and vane(s) to the outlet, where the gas exits the system. The oil acts as a lubricant and also allows the pumping of some corrosive gases, as it protects the metal to some degree. Although this pump is quite fast and efficient for obtaining pre vacuum, it also may contaminate the vacuum system with oil. Therefore the use of oil traps is highly recommended.

Scroll Pump


Scroll pump (scroll compressor) is an oil-free vacuum pump used for obtaining ‪#‎prevacuum‬ with a level of 0.1 mbar. The ‪#‎scrollpump‬ is based on two scrolls, that are placed insede the working chamber. One of these scrolls is fixed and the other one mobile. Once the gas enters the system through the inlet, it gets carried to the outlet in the middle by the mobile orbiting scroll. This is possible due to the fact that during the mobile scrolls movement a wide gap is locally kept between the two scrolls and the gap moves to the middle, carrying the gas in it. As the volume of the gap decreases at the outlet, the gas is pushed out of the system. Due to wear the orbiting scroll needs to be replaced about twice a year.



The ‪#‎cryopump‬ is a high vacuum pump that is based on the adsorption of gas on cold surfaces. The cooler the surface – the better the pumping! For that purpose liquid helium is often used for cooling the system parts as it is extremely cold, having a temperature only four degrees above absolute zero. The pumping is done in multiple stages, where each stage has a different temperature. The „warmest“ part is the first stage, that has a temperature of 100 degrees Kelvin (or lower) and that causes water to condensate on it. During the ‪#‎condensation‬ of water also some other gases may also be trapped under the water and that process is called ‪#‎cryotrapping‬. However, in order to effectively pump gases such as nitrogen, even colder surfaces (less than 17 degrees Kelvin) are required. In this stage the metal may also be coated with porous activated charcoal and that allows to adsorb even smaller gas molecules such as helium and even hydrogen (this is called ‪#‎cryosorption‬ ). So basically the pumping of gases with this ‪#‎vacuumpump‬ is based on three processes: condensation, cryotrapping and cryosorption.

Titanium Sublimation Pump

The titanium sublimation pump is a vacuum pump used as a part of vacuum systems in order to briefly improve the level of ‪#‎vacuum‬. The working principle is relatively simple. A pulsing current passes through a titanium filament, causing it to sublimate (goes directly from solid phase to gas phase). The fresh titanium chemically reacts with gas in the vacuum chamber, creating a solid product that deposits on the chamber walls. As the walls are also coated with highly reactive freshly deposited titanium, they may also chemically bind gas molecules that interact with them. Some gases may not chemically bind with titanium but can still be physically trapped under the titanium atoms on the chambers walls.

Ion Pump


The ion pump is a high vacuum pump that is based on ionizing the gas. When the gas that enters the ‪#‎ionpump‬ it always has some ions in it and those are pulled towards the titanium cathode. These ions are then trapped between the titanium atoms and they may also chemically react with titanium forming solid titanium nitride or titanium oxide, depending on the gas. In addition electrons and titanium atoms are emitted from the cathode when bombarded by the ionized gas molecules. These electrons are then accelerated towards the steel anode as the potential between the anode and cathode is thousands of volts. A magnetic field caused by the magnets makes the electrons move spirally so they spend more time in the open and more likely hit gas molecules to ionize them. The generated gas ions move again towards the cathode and kick out even more electrons and titanium atoms. Some of the kicked out titanium atoms also deposit on the anode and in this process bury gas molecules under them. The pump may work for several years if used in high vacuum environment and if the amount of pumped gas is not large. At some point however the cathodes need to be replaced.

Turbomolecular Pump


Turbomolecular pump ( ‪#‎TMP‬ ) is a popular high vacuum pump, that is widely used in many vacuum systems (electron microscopes for example) as it is clean, fast and efficient for maintaining high vacuum over a long period of time. Inside the pump there are rotor blades that rotate with a speed up to 90 000 rotations per minute and stator blades that are stationary. If a gas molecule enters the pump then it is hit by the rotor blades that are tilted at a certain angle. The kinetic energy from the blade is transfered to the gas molecule and causes it to move down and hit a stator blade that is also tilted at a certain angle, causing the molecule to „bounce“ down, where it meets the next rotor blade. Eventually the gas molecules reach the bottom of the turbomolecular pump where they are removed with a backing pump (prevacuum pump). The turbomolecular pump usually also needs a pre-vacuum before it can work efficiently and this can be done with a pre-vacuum pump (for example a scroll compressor pump). Once the pressure is low enough, the ‪#‎turbomolecularpump‬ starts working and the rotation speed of the rotor blades is gradually increased.