Tag Archives: voltage

How to Generate Hydrogen by Splitting Water

Hydrogen is the most abundant substance in the universe. It fuels the starts that light the nightsky. Hydrogen will also power the future of mankind as it is already used as car fuel and within this century even in fusion reactors.

As most of you know, a water molecule consists of one oxygen atom and two hydrogen atoms. So in order to get hydrogen, it is needed to split the water molecule. This can be done for example electrochemically where an electrical potential is applied between electrodes in a salt water. For a home experiment one can simply put a 9 V battery into salt water and watch how hydrogen bubbles start to form at the cathode. At the same time oxygen is generated at the anode but since the anode on the battery is usually made of steel, it will quickly corrode as it reacts with chlorine and oxygen. This causes the salt water to go brown. So instead, you may want to use electrodes instead that are connected to an external power source. If a DC voltage is used then especially the anode needs to be made from a chemically inert conductive material such as platinum which doesnt oxidize. At this anode oxygen gas can be collected. At the same time hydrogen gas is generated at the cathode and can also be collected. If DC voltage is used then the electrode at cathodic potentials will not corrode very quickly as oxidation cannot occur. However hydrogen damage may eventually destroy the electrode.

Hydrogen damage occurs when the small atomic hydrogen generated at the cathode moves into pores and cracks inside the electrode and combines with other hydrogen atom to form molecular hydrogen. The molecular hydrogen however is too large to diffuse through metal and starts building up inside the sealed crack or pore and pressure increases until it splits the material.

In order to produce as much gas as possible, the surface area of electrodes needs to be increased. Make the electrodes rough, multilayered or highly porous for greater surface area.

If AC voltage is used to split water, then corrosion is suppressed and for some time even stainless steel can be used as both electrodes.


If you found this video useful, feel free to support me with 5 eur / usd via Paypal




Scanning Electron Microscopy (SEM)

Scanning Electron Microscopy

The scanning electron microscope is a powerful tool used by many scientists for studying and developing materials. This device uses electrons instead of photons and that allows the operator to visualize even nano-scaled surface details. Therefore it is very useful for also studying corrosion processes and creating efficient thin coatings which have a thickness of less than a micrometer.

In the video above you will see the working principle of this microscope and how it is operated.

The electrons are generated in the electron gun on top of the microscope. There are different source types but one of the oldest used is a tungsten filament that is heated over 2400 degrees celsius by passing a current through it. At this temperature electrons emit from the filament and are pulled down the column with the help of an anode. The operator selects the voltage that accelerates the electrons. It can be up to 30 kV in conventional scanning electron microscopes. The accelerated electrons are scattered and need to be focused – this is done with the help of multiple focusing lenses. These lenses also tune the amount of electrons that reach the sample. For example by broadening the electron beam, the electrons are absorbed by the column and dont reach the sample. In order to scan across the sample row by row, the electron beam needs to be moved in such a manner. This is achieved with the help of scanning coils that are placed below the focusing lenses. The final focusing of the beam is done with objective lenses located below the scanning coils. In order to get an image of the substrate the surface is scanned row by row with the electron beam. In each spot signals like secondary electrons, backscattered electrons or characteristic X-Rays are generated. By detecting the signal emitted from each scanned spot, an image of the surface is generated. So for example by detecting secondary electrons a secondary electron image is generated.

Secondary electrons are generated when the primary beam electrons kick out electrons from the substrate atoms. In that process primary beam electrons lose energy as it is transfered to the secondary electrons. These secondary electrons generaly have low energy and escape only from near the surface, giving a good image of the substrates topography. The electrons are collected with a special detector that has a positively charged collector  for pulling the negatively charged electrons towards it.

Backscattered electrons are primary beam electrons that are scattered back in a similar direction as they interact with the substrate atoms nucleous. In that process they dont lose much energy and can be emitted even from deep layers of the substrate. Therefore they carry the bulk information of the sample and generated images are not completely topographic. The electron yield strongly depends on the atomic number of the substrate. For example regions on substrate with higher atomic number appear brighter on the image as more electrons are backscattered in these regions.

Characteristic X-Rays are generated when sample atoms exited by primary beam electrons are undergoing a relaxation process where the inner shell vacant spot is filled with an outer shell electron. The emitted radiations energy depends strictly on the atoms number and on the electrons binding energies that are involved in this process. Therefore this signal can be used to detect different elements and do quantitative element analysis.

For a real SEM study the sample first needs to be prepared – it has to be dry, conductive and with a suitable size. Non-conductive samples can be coated with a thin (couple nanometers) layer of metal (Au, Pt..), which allows SEM studies as they conduct away the heat and negative charge caused by electrons. The sample is moved into the microscope through an airlock or the main chamber door and placed on a stage with a special holder. The stage can move in any desired direction (x,y,z, rotate, tilt). The sample is then moved under the electron column to a suitable working distance. After focusing and other adjustments the first electron image can be taken.

Element microanalysis can be done in several ways but first an electron image of the sample is obtained. The most common way to do element analysis is selecting a characteristic spot on the sample and then bombard it with the narrow (couple nm wide) electron beam. As a result X-Rays are emitted from the couple micrometer wide interaction volume. This gives information from a very localized area but in some cases an average composition of the material is needed. For that a larger area (lets say 50 x 50 microns) is bombarded by electrons and the X-Rays emitted from that area are detected. It is also possible to map the distribution of elements on a larger area by scanning across the surface with the electrons row by row and collect X-Rays from each scanned point. Based on the detected X-Rays an image is created that shows the distribution of certain elements.

In order to see what is inside a material a focused ion beam (FIB) is used to make  a cross-section or a thin lamella. The cross-sections or lamella are then studied with electrons at a suitable angle by tilting it with the help of the stage.

Scanning electron microscopes generally work in a high vacuum in order to prevent surface contamination and electron or x-ray interactions with the gas in the chamber which would affect the quality of the image. However there are also specially designed environmental scanning electron microscopes (ESEM-s), that work in low vacuum. The ESEM can therefore even be used to study living cells or bacteria.